Guide

How to String Outdoor Lights on Poles

Updated on · By the Joe Joslin Outdoors team

To string outdoor lights on poles, measure your space, set poles at even heights, then hang the strand with a gentle sag and secure both ends. Keep cords clear of walkways and water, and check the load and ratings before you start.

On this page (8 sections)
  1. How do you plan the layout before you hang anything?
  2. What poles work best for hanging light strands?
  3. What spacing and sag look best between poles?
  4. How do you hang the lights step by step?
  5. How do you keep strands safe outdoors?
  6. How do you handle wind, rain, and seasonal change?
  7. Which poles suit decks, yards, and planters?
  8. How do you choose the right setup for your space?

To string outdoor lights on poles, measure your space, set poles at even heights, then hang the strand with a gentle sag and secure both ends. Keep cords clear of walkways and water, and check the load and ratings before you start.

That short version is how to string outdoor lights on poles in plain steps. The rest of this guide explains how to choose poles, plan spacing, hang the lights, and check safety without turning your patio into a tangle.

How do you plan the layout before you hang anything?

Plan the layout on paper first, because pole placement decides how straight and even the strands will look. Sketch your patio, deck, or yard, and mark where you want light, where people walk, and where furniture sits.

For fixed accent lighting, compare solar deck lights.

Measure each side where a strand will run. Divide the length by the strand length you own, then add poles where the math leaves a gap.

A strand that must stretch to reach will sag too much or pull on its ends.

Note the power source at the same time. String lights need an outlet or a battery pack, and a long cord across the floor is a trip risk.

For a solar-powered option, compare outdoor solar string lights.

Put a pole near the outlet, or plan a strand that starts at the wall.

Think about height as you sketch. Poles around 10 feet tall are common in the products below, and that height keeps bulbs over heads when you stand under them.

Bracket spots matter too. If a fence, wall, or eave can hold one end, you may need fewer ground poles.

What poles work best for hanging light strands?

Choose poles by height, base style, and how the top holds the strand. The pole must stand steady in wind, hold the strand without bending, and suit the surface under it.

Metal poles are a common choice for outdoor use. AILBTON makes a 10 foot metal pole in a 4 pack with fence brackets, which suits people who want to mix wall mounts and freestanding posts.

NSHWFW makes a 6 pack of 10 foot poles with height adjustment and hooks. Each pole can be set to a height that fits the scene, and the fork base can go into grass or soil, with brackets for decks or fences.

AHRLHR makes a 6 pack of 10 foot metal poles with a V-shaped head and fence brackets. The V head gives you a wider point to rest a strand, banner, or lantern, and the height adjusts to a maximum of 10 feet.

Our roundup of best outdoor string light poles compares more base styles. Our guide to best tall poles for string lights helps if you need extra clearance over a table or path.

What spacing and sag look best between poles?

Space poles so each span matches the strand you own, with a small sag left over. Measure pole to pole and compare it with the strand length for that span.

A gentle sag of about 6 inches to 1 foot is a good start. It keeps tension off the wire and leaves room for wind, while too much sag can drop bulbs into head range.

Place poles in a simple shape first, such as a rectangle around seating, a line along a fence, or a zigzag over a dining table.

Walk the pattern after setting the poles. Stand where guests will sit and walk, and move a pole if a strand crosses a doorway at head height.

If you plan to use planters, our guide to best string light poles in planters covers weight and base fit. The pole must sit firm without tipping when the strand pulls.

How do you hang the lights step by step?

Hang the lights in order, because setting poles first keeps the strand from tangling on the ground. Install each pole, check it stands plumb, then run the strand from one pole to the next.

Start at the power source if your strand is corded. That way you know the plug end is in the right place before the rest of the run goes up.

If you run out of reach, you can move a pole while the job is still easy.

Loop or hook the strand over the pole head, then walk to the next pole. Keep the wire in one hand so it does not drag or twist, and set the same sag you used on the first span.

Secure both ends before you add a second strand. Give each hook or bracket a light pull to check it, then step back and adjust the pole head so bulbs sit at one level.

For a deck, our list of best string light poles for deck shows bracket options that suit rails and boards, so match the base to the surface.

How do you keep strands safe outdoors?

Keep safety simple and strict: use outdoor-rated lights, keep plugs dry and off the ground, and do not overload an outlet. Do not use a damaged strand, plug, or pole.

Check the rating on your lights before you hang them. Outdoor strands are made for sun, rain, and temperature swings in ways indoor strands are not.

Our safety guide asks are outdoor string lights safe in the rain and explains what to look for on the label.

Keep connections out of puddles and away from sprinklers, and raise them where they can drip dry. Do not run cords under rugs, through doorways, or across walkways, where they can pinch, hide damage, and create a trip risk.

Route the cord along a wall or fence where you can see it. Check the load on each pole before adding extras, since a pole that wobbles under one strand will not improve with a second strand or added banners.

NSHWFW says its poles are rustproof and water resistant, and AHRLHR says its poles are rustproof, which helps in humid spots.

How do you handle wind, rain, and seasonal change?

Expect the strand to move, because wind will pull on any line you hang between two points. A little movement is fine, and a pole that leans or a hook that slips is not.

Set ground poles deep enough to hold firm in soft soil. A fork base helps in grass, but wet soil after rain can still loosen.

Check poles after a storm and push them firm again before the next use.

Take strands down in high wind if the maker advises it. Storage in a dry place protects the wire and bulbs through the off season.

Coil the strand in a wide loop, not a tight wrap, so the wire does not kink.

Wipe poles and hooks with a dry cloth when they get dusty. Metal poles that stay wet for long periods can develop surface wear, so dry storage helps.

AHRLHR lists its pole as outdoor use, and NSHWFW lists its pole as water resistant.

If you want a timer so lights come on at dusk, our list of best outdoor string lights with timer covers that feature. An outdoor smart plug is another way to schedule an outlet.

A timer also keeps you from leaving lights on all night by habit.

Which poles suit decks, yards, and planters?

Match the pole to the surface, because a bracket mount and a ground fork do different jobs. A deck rail, a lawn, and a planter each need a base that fits the spot.

Decks suit bracket mounts on rails or posts. You fix the bottom to wood and keep the pole upright.

That keeps the deck floor clear and avoids drilling into the deck boards.

Lawns and garden beds suit fork bases that push into soil. NSHWFW includes a fork for grass or soil plus brackets and screws for deck or fence use.

That mix suits people who move the pattern between spots.

Planters suit poles with a narrow base that fits the pot. Check the pot width and depth before you buy, then set the pole so the strand pull does not tip the planter.

Walls and fences suit bracket poles where you have no floor space. AILBTON includes fence brackets for use on walls, fences, and eaves.

For strand choice, see best outdoor string lights. For light choice, see our guide to led patio lights.

How do you choose the right setup for your space?

Choose the setup that fits your space, because a small patio and a large yard need different pole counts and heights. Count the spans you need, then pick a pack that covers them without forcing a long stretch.

A 4 pack suits a small rectangle or a line along one fence. A 6 pack suits a larger seating area or a pattern with a center pole, so buy the count you need.

Pick adjustable poles if your ground slopes or if you want to change height for a party. Pick fixed brackets for a permanent mount on a fence or rail.

Pick a V head for an easy rest point for the strand. It gives the wire a wider point to sit on and helps keep the line level.

Match the lights to the poles after you set the pattern, since a short span suits a short strand.

For a long span, a longer strand or a center pole will keep the sag even. Then hang one span, step back, and adjust before you hang the rest.

For a final check of pole styles, reread our best outdoor string light poles guide. Measure first, set poles level, hang with a gentle sag, and keep plugs dry.

Frequently asked questions

How tall should poles be for outdoor string lights?

Most patios work well with poles in the 9 to 10 foot range, because that height clears heads and leaves room for a gentle sag between poles. Measure your space and doorways first, then choose a height that keeps bulbs above seating and walkways.

How much sag should string lights have between poles?

A gentle sag of about 6 inches to 1 foot over a typical patio span looks even and reduces strain on the strand. Tighter spans need less sag, and longer spans need a little more, so adjust after you hang the first run.

Can you hang string lights on poles in the rain?

Only use lights and poles rated for outdoor use, and keep plugs and connections off the ground and away from standing water. Our guide on whether outdoor string lights are safe in the rain covers ratings and safe setup.